Interlocking concrete blocks are the most common way to build a retaining wall in Kelowna and the Okanagan. They’re made in a factory to consistent sizes, they stack without mortar, and they can be reinforced with geogrid to hold back tall, steep slopes. This guide explains the main types of retaining wall blocks, what sizes they come in and what a block wall costs to install, so you can talk to contractors with confidence.

Types of Retaining Wall Blocks
| Block type | Typical use | Notes |
|---|---|---|
| Small garden-wall blocks | Planters, edging and walls under about 2 ft | Light enough to place by hand. Not meant to hold back a real slope. |
| Standard segmental blocks | Most residential walls, terraces and walls beside driveways | About 1 sq. ft. of wall face per block. Can be reinforced with geogrid for taller walls. |
| Large-format blocks | Tall walls, commercial sites and walls that carry heavy loads | Can weigh a tonne or more each and are set with a machine. Their weight does much of the work. |
| Cap units | The top course of any block wall | Finish the wall, shed water and give a place to sit on low walls. |
How the blocks lock together
- Lip or rear-lug blocks: a ridge on the back of each block hooks over the course below and sets each row back slightly, so the wall leans into the slope.
- Pinned blocks: fibreglass or plastic pins connect the courses and control the setback.
- Hollow-core blocks: the cores are filled with drain rock as the wall goes up, which adds weight and helps water drain.
Common sizes and weights
A typical standard block is about 8 inches high, 18 inches wide and 11–12 inches deep, and weighs around 75 lb (34 kg). Allan Block’s AB Classic, one of the most widely used systems, is 75 lb with a built-in 6° setback (source: Allan Block product information). Sizes and weights vary by manufacturer, so check the spec sheet for the block your contractor recommends.
How Tall Can a Block Wall Be?
Every block system has a maximum height it can reach on its own weight (a “gravity wall”). Above that, layers of geogrid are buried in the backfill to tie the wall into the slope. The height limit depends on the block, the soil, the slope above the wall and any load on top of it, such as a driveway or a house.
- In most Okanagan municipalities, walls over about 1.2 m (4 ft), or walls supporting a driveway, building or steep slope, need an engineered design and may need a permit. See our guide to retaining wall permits in the Okanagan.
- Terracing a slope into two or more shorter walls can sometimes avoid engineering, but only if the walls are far enough apart. Ask before you assume.
- Manufacturers’ height charts generally don’t account for earthquake loads. The Okanagan is in a seismic zone, so taller walls should be checked by an engineer.
What Makes a Block Wall Last
The blocks themselves rarely fail. Walls lean, bulge or crack because of what’s behind and under them:
- Compacted gravel base: a level, compacted base below the first course, with the first block partly buried.
- Drainage: clean drain rock behind the wall and a perforated pipe at the bottom that carries water away. Okanagan clay and spring snowmelt make this essential.
- Geogrid where needed: on taller or loaded walls, installed at the spacing and lengths the engineer or manufacturer specifies.
- Filter fabric: keeps fine soil from clogging the drain rock.
If you already have a wall that’s moving, see how to fix a leaning retaining wall.
Block Wall Costs in the Okanagan
| Item | Typical installed cost |
|---|---|
| Interlocking concrete block wall | $35 – $65 per sq. ft. of wall face |
| Example: 3 ft high × 30 ft long (90 sq. ft.) | about $3,150 – $5,850 |
| Engineered design for taller walls | often $1,500 – $3,500 |
Prices include excavation, base, drainage and the wall itself. Steep sites, poor access, removing an old wall and premium block finishes add cost. For the full breakdown, see our retaining wall and paver patio cost guide, and compare materials in timber vs block vs natural stone.
Retaining Wall Block FAQs
Can I build a block retaining wall myself?
Low garden walls, yes. Walls that hold back a real slope, sit near a driveway or house, or need geogrid are best left to an experienced contractor, and taller walls usually need an engineer’s design. See our guide to choosing a retaining wall contractor.
Which block brand is best?
Most major segmental systems perform well when they’re installed to the manufacturer’s specifications. Availability matters more: contractors usually work with the systems local suppliers stock, which keeps replacement blocks and caps easy to find.
Do block walls need a permit in Kelowna?
Usually only above about 1.2 m, or when the wall supports a driveway, building or steep slope. Rules vary, so confirm with the City of Kelowna before work starts. Our Kelowna retaining walls page covers local height limits.
Ready to build? See our page on concrete block retaining walls.
Get a Free Block Wall Estimate
Tell us about your wall and a local retaining wall contractor will be in touch to arrange a free estimate. Prefer to talk? Call 257-883-1211.